. After studying this section, you should be able to:. Understand the principles of Boost Converters. The switching transistor.
Practical Design of Buck Converter PECON 2008, Johor Bahru, Malaysia Taufik Page 24 Sizing Switch: Voltage Rating.With ideal diode, the V switch-max = V inmax. For non-ideal diode, V switch-max = V inmax + V F where V F is the maximum forward drop across the diode (calculated at maximum load current). Use safety factor of at least 20%.
The flywheel circuit. Recognise the limitations on the output voltage. Recognise different input sources.
Understand the relationship between switching pulse width and output voltage.Boost ConverterSwitched mode supplies can be used for many purposes including DC to DC converters. Often, although a DC supply, such as a battery may be available, its available voltage is not suitable for the system being supplied. For example, the motors used in driving electric automobiles require much higher voltages, in the region of 500V, than could be supplied by a battery alone. Even if banks of batteries were used, the extra weight and space taken up would be too great to be practical. The answer to this problem is to use fewer batteries and to boost the available DC voltage to the required level by using a boost converter. Another problem with batteries, large or small, is that their output voltage varies as the available charge is used up, and at some point the battery voltage becomes too low to power the circuit being supplied. However, if this low output level can be boosted back up to a useful level again, by using a boost converter, the life of the battery can be extended.The DC input to a boost converter can be from many sources as well as batteries, such as rectified AC from the mains supply, or DC from solar panels, fuel cells, dynamos and DC generators.
The boost converter is different to the in that it’s output voltage is equal to, or greater than its input voltage. However it is important to remember that, as power (P) = voltage (V) x current (I), if the output voltage is increased, the available output current must decrease. 3.2.2 Boost Converter Operation at Switch OnFig 3.2.2 illustrates the circuit action during the initial high period of the high frequency square wave applied to the MOSFET gate at start up. During this time MOSFET conducts, placing a short circuit from the right hand side of L1 to the negative input supply terminal.
Therefore a current flows between the positive and negative supply terminals through L1, which in its. There is virtually no current flowing in the remainder of the circuit as the combination of D1, C1 and the load represent a much higher impedance than the path directly through the heavily conducting MOSFET. 3.2.3 Current Path with MOSFET OffFig. 3.2.3 shows the current path during the low period of the switching square wave cycle.
As the MOSFET is rapidly turned off the sudden drop in current causes L1 to produce a in the opposite polarity to the voltage across L1 during the on period, to keep current flowing. This results in two voltages, the supply voltage V IN and the back e.m.f.(V L) across L1 in series with each other.This higher voltage (V IN +V L), now that there is no current path through the MOSFET, forward biases D1. The resulting current through D1 charges up C1 to V IN +V L minus the small forward voltage drop across D1, and also supplies the load.
3.2.4 Current Path with MOSFET OnFig.3.2.4 shows the circuit action during MOSFET on periods after the initial start up. Each time the MOSFET conducts, the cathode of D1 is more positive than its anode, due to the charge on C1. D1 is therefore turned off so the output of the circuit is isolated from the input, however the load continues to be supplied with V IN +V L from the charge on C1.
Although the charge C1 drains away through the load during this period, C1 is recharged each time the MOSFET switches off, so maintaining an almost steady output voltage across the load.The theoretical DC output voltage is determined by the input voltage (V IN) divided by 1 minus the duty cycle (D) of the switching waveform, which will be some figure between 0 and 1 (corresponding to 0 to 100%) and therefore can be determined using the following formula: Example:If the switching square wave has a period of 10µs, the input voltage is 9V and the ON is half of the periodic time, i.e. 5µs, then the output voltage will be:V OUT = 9/(1- 0.5) = 9/0.5 = 18V (minus output diode voltage drop)Because the output voltage is dependent on the duty cycle, it is important that this is accurately controlled. For example if the duty cycle increased from 0.5 to 0.99 the output voltage produced would be:V OUT = 9/(1- 0.99) = 9/0.01 = 900VBefore this level of output voltage was reached however, there would of course be some serious damage (and smoke) caused, so in practice, unless the circuit is specifically designed for very high voltages, the changes in duty cycle are kept much lower than indicated in this example. 3.2.5 Boost Converter Animation Click play to start.See the current paths during the on and off periods of the switching transistor.See the magnetic field around the inductor grow and collapse, and observe the changing polarity of the voltage across L.Watch the effect of ripple during the on and off states of the switching transistor.See the input voltage and the back e.m.f.
Of V L add to give an output voltage greater than the input voltage. Click pause to hold the animation in either the on or the off state. Click back to reset the animation. 3.2.6 Typical I.C. Boost Converter (LM27313)Because of the ease with which boost converters can supply large over voltages, they will almost always include some regulation to control the output voltage, and there are many I.Cs. Manufactured for this purpose A typical example of an I.C. Boost converter is shown in Fig.
3.2.6, in this example the from. This chip is designed for use in low power systems such as PDAs, cameras, mobile phones, and GPS devices.In this circuit, an appropriate fraction of the output voltage (V OUT), dependent on the ratio of R2:R3 is used as a sample and compared with a reference voltage within the I.C. This produces an error voltage that is used to alter the duty cycle of the switching oscillator, enabling a range of automatically regulated boost voltages between 5V and 28V to be obtained.The contains an internal oscillator operating at a fixed frequency of about 1.6MHz. The FET switching transistor is also internal and switches the current through L1 via the SW terminal. Notice also that a Schottky diode with an appropriate voltage and current rating is used for D1 to keep losses due to the forward voltage drop of the diode as small as possible, and to enable high switching speeds to be achieved. Also has a shut down (SHDN) facility, operated by external logic, by which the boost converter may be disabled when not required, to save battery power. Protection CircuitsOther safety features provided by the I.C.
![Boost Boost](http://www.rroij.com/articles-images/IJIRSET-1461-t003.gif)
Are over current shut down, which disables the switch on a cycle-by-cycle basis if too much current is sensed, and an over temperature shut down facility. StabilityAnother problem facing designers of high frequency boost converters is that of stability, as at MHz frequencies both negative and positive feedback can occur simply due to electromagnetic fields radiating between components within the circuit, especially where the circuit components are in very close proximity as in surface mount layouts. C2 is therefore added to improve stability and prevent possible oscillation due to unwanted positive feedback occurring.
The basic schematic of an inverting buck–boost converter.The buck–boost converter is a type of that has an output voltage magnitude that is either greater than or less than the input voltage magnitude. It is equivalent to a using a single inductor instead of a transformer.Two different topologies are called buck–boost converter.Both of them can produce a range of output voltages, ranging from much larger (in absolute magnitude) than the input voltage, down to almost zero.The inverting topology The output voltage is of the opposite than the input. This is a with a similar circuit topology to the and the. The output voltage is adjustable based on the of the switching transistor.
One possible drawback of this converter is that the switch does not have a terminal at ground; this complicates the driving circuitry. However, this drawback is of no consequence if the power supply is isolated from the load circuit (if, for example, the supply is a battery) because the supply and diode polarity can simply be reversed. When they can be reversed, the switch can be on either the ground side or the supply side. A combined with a The output voltage is typically of the same polarity of the input, and can be lower or higher than the input.
Such a non-inverting buck-boost converter may use a single inductor which is used for both the buck inductor mode and the boost inductor mode, using switches instead of diodes, sometimes called a 'four-switch buck-boost converter', it may use multiple inductors but only a single switch as in the and topologies.